This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 1691, EID 1692, EID 2785, EID 2786, EID 3868
Network Working Group                                           C. Daboo
Request for Comments: 5464                                   Apple, Inc.
Category: Standards Track                                  February 2009


                      The IMAP METADATA Extension

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Abstract

   The METADATA extension to the Internet Message Access Protocol
   permits clients and servers to maintain "annotations" or "metadata"
   on IMAP servers.  It is possible to have annotations on a per-mailbox
   basis or on the server as a whole.  For example, this would allow
   comments about the purpose of a particular mailbox to be "attached"
   to that mailbox, or a "message of the day" containing server status
   information to be made available to anyone logging in to the server.

Table of Contents

   1.  Introduction and Overview  . . . . . . . . . . . . . . . . . .  3
   2.  Conventions Used in This Document  . . . . . . . . . . . . . .  3
   3.  Data Model . . . . . . . . . . . . . . . . . . . . . . . . . .  4
     3.1.  Overview . . . . . . . . . . . . . . . . . . . . . . . . .  4
     3.2.  Namespace of Entries . . . . . . . . . . . . . . . . . . .  4
       3.2.1.  Entry Names  . . . . . . . . . . . . . . . . . . . . .  5
     3.3.  Private versus Shared and Access Control . . . . . . . . .  6
   4.  IMAP Protocol Changes  . . . . . . . . . . . . . . . . . . . .  7
     4.1.  General Considerations . . . . . . . . . . . . . . . . . .  7
     4.2.  GETMETADATA Command  . . . . . . . . . . . . . . . . . . .  8
       4.2.1.  MAXSIZE GETMETADATA Command Option . . . . . . . . . .  9
       4.2.2.  DEPTH GETMETADATA Command Option . . . . . . . . . . . 10
     4.3.  SETMETADATA Command  . . . . . . . . . . . . . . . . . . . 10
     4.4.  METADATA Response  . . . . . . . . . . . . . . . . . . . . 12
       4.4.1.  METADATA Response with Values  . . . . . . . . . . . . 13
       4.4.2.  Unsolicited METADATA Response without Values . . . . . 13
   5.  Formal Syntax  . . . . . . . . . . . . . . . . . . . . . . . . 14
   6.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 16
     6.1.  Entry and Attribute Registration Template  . . . . . . . . 16
     6.2.  Server Entry Registrations . . . . . . . . . . . . . . . . 16
       6.2.1.  /shared/comment  . . . . . . . . . . . . . . . . . . . 17
       6.2.2.  /shared/admin  . . . . . . . . . . . . . . . . . . . . 17
     6.3.  Mailbox Entry Registrations  . . . . . . . . . . . . . . . 17
       6.3.1.  /shared/comment  . . . . . . . . . . . . . . . . . . . 18
       6.3.2.  /private/comment . . . . . . . . . . . . . . . . . . . 18
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 18
   8.  Normative References . . . . . . . . . . . . . . . . . . . . . 19
   Appendix A.  Acknowledgments . . . . . . . . . . . . . . . . . . . 19

1.  Introduction and Overview

   The goal of the METADATA extension is to provide a means for clients
   to set and retrieve "annotations" or "metadata" on an IMAP server.
   The annotations can be associated with specific mailboxes or the
   server as a whole.  The server can choose to support only server
   annotations or both server and mailbox annotations.

   A server that supports both server and mailbox annotations indicates
   the presence of this extension by returning "METADATA" as one of the
   supported capabilities in the CAPABILITY command response.

   A server that supports only server annotations indicates the presence
   of this extension by returning "METADATA-SERVER" as one of the
   supported capabilities in the CAPABILITY command response.

   A server that supports unsolicited annotation change responses MUST
   support the "ENABLE" [RFC5161] extension to allow clients to turn
   that feature on.

   The METADATA extension adds two new commands and one new untagged
   response to the IMAP base protocol.

   This extension makes the following changes to the IMAP protocol:

   o  adds a new SETMETADATA command

   o  adds a new GETMETADATA command

   o  adds a new METADATA untagged response

   o  adds a new METADATA response code

   The rest of this document describes the data model and protocol
   changes more rigorously.

2.  Conventions Used in This Document

   In examples, "C:" and "S:" indicate lines sent by the client and
   server, respectively.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   Whitespace and line breaks have been added to the examples in this
   document to promote readability.

3.  Data Model

3.1.  Overview

   Mailboxes or the server as a whole may have zero or more annotations
   associated with them.  An annotation contains a uniquely named entry,
   which has a value.  Annotations can be added to mailboxes when a
   mailbox name is provided as the first argument to the SETMETADATA
   command, or to the server as a whole when the empty string is
   provided as the first argument to the command.

      For example, a general comment being added to a mailbox may have an 
  entry name of "/shared/comment" and a value of "Really useful
   mailbox".
EID 1691 (Verified) is as follows:

Section: 3.1,2nd para

Original Text:

   For example, a general comment being added to a mailbox may have an
|  entry name of "/comment" and a value of "Really useful mailbox".
                  ^^^^^^^^

Corrected Text:

   For example, a general comment being added to a mailbox may have an
|  entry name of "/shared/comment" and a value of "Really useful
   mailbox".
Notes:
Rationale:
The example given in the Original Text violates the rules for
the formation of entry names specifcied later in the RFC
(cf. section 3.2 ff.), and is therefore considered confusing.
The protocol changes to IMAP described below allow a client to access or change the values of any annotation entry, assuming it has sufficient access rights to do so. 3.2. Namespace of Entries Each annotation is an entry that has a hierarchical name, with each component of the name separated by a slash ("/"). An entry name MUST NOT contain two consecutive "/" characters and MUST NOT end with a "/" character. The value of an entry is NIL (has no value), or a string or binary data of zero or more octets. A string MAY contain multiple lines of text. Clients MUST use the CRLF (0x0D 0x0A) character octet sequence to represent line ends in a multi-line string value. Entry names MUST NOT contain asterisk ("*") or percent ("%") characters and MUST NOT contain non-ASCII characters or characters with octet values in the range 0x00 to 0x19. Invalid entry names result in a BAD response in any IMAP command in which they are used. Entry names are case-insensitive. Use of control or punctuation characters in entry names is strongly discouraged. This specification defines an initial set of entry names available for use with mailbox and server annotations. In addition, an extension mechanism is described to allow additional names to be added for extensibility. The first component in entry names defines the scope of the annotation. Currently, only the prefixes "/private" or "/shared" are defined. These prefixes are used to indicate whether an annotation is stored on a per-user basis ("/private") and not visible to other users, or whether an annotation is shared between authorized users ("/shared") with a single value that can be read and changed by authorized users with appropriate access. See Section 3.3 for details. Entry names can have any number of components starting at 2, unless they fall under the vendor namespaces (i.e., have a /shared/vendor/ <vendor-token> or /private/vendor/<vendor-token> prefix as described below), in which case they have at least 4 components. 3.2.1. Entry Names Entry names MUST be specified in a Standards Track or IESG-approved Experimental RFC, or fall under the vendor namespace. See Section 6.1 for the registration template. 3.2.1.1. Server Entries These entries are set or retrieved when the mailbox name argument to the new SETMETADATA or GETMETADATA command is the empty string. /shared/comment Defines a comment or note that is associated with the server and that is shared with authorized users of the server. /shared/admin Indicates a method for contacting the server administrator. The value MUST be a URI (e.g., a mailto: or tel: URL). This entry is always read-only -- clients cannot change it. It is visible to authorized users of the system. /shared/vendor/<vendor-token> Defines the top level of shared entries associated with the server, as created by a particular product of some vendor. This entry can be used by vendors to provide server- or client-specific annotations. The vendor-token MUST be registered with IANA, using the Application Configuration Access Protocol (ACAP) [RFC2244] vendor subtree registry. /private/vendor/<vendor-token> Defines the top level of private entries associated with the server, as created by a particular product of some vendor. This entry can be used by vendors to provide server- or client-specific annotations. The vendor-token MUST be registered with IANA, using the ACAP [RFC2244] vendor subtree registry. 3.2.1.2. Mailbox Entries These entries are set or retrieved when the mailbox name argument to the new SETMETADATA or GETMETADATA command is not the empty string. /shared/comment Defines a shared comment or note associated with a mailbox. /private/comment Defines a private (per-user) comment or note associated with a mailbox. /shared/vendor/<vendor-token> Defines the top level of shared entries associated with a specific mailbox, as created by a particular product of some vendor. This entry can be used by vendors to provide client-specific annotations. The vendor-token MUST be registered with IANA, using the ACAP [RFC2244] vendor subtree registry. /private/vendor/<vendor-token> Defines the top level of private entries associated with a specific mailbox, as created by a particular product of some vendor. This entry can be used by vendors to provide client- specific annotations. The vendor-token MUST be registered with IANA, using the ACAP [RFC2244] vendor subtree registry. 3.3. Private versus Shared and Access Control In the absence of the ACL (Access Control List) extension [RFC4314], users can only set and retrieve private or shared mailbox annotations on a mailbox that exists and is returned to them via a LIST or LSUB command, and on which they have either read or write access to the actual message content of the mailbox (as determined by the READ-ONLY and READ-WRITE response codes as described in Section 5.2 of [RFC4314]). When the ACL extension [RFC4314] is present, users can only set and retrieve private or shared mailbox annotations on a mailbox on which they have the "l" right and any one of the "r", "s", "w", "i", or "p" rights. If a client attempts to set or retrieve annotations on mailboxes that do not satisfy the conditions above, the server MUST respond with a NO response. Users can always retrieve private or shared server annotations if they exist. Servers MAY restrict the creation of private or shared server annotations as appropriate. When restricted, the server MUST return a NO response when the SETMETADATA command is used to try to create a server annotation. If the METADATA extension is present, support for shared annotations is REQUIRED, whilst support for private annotations is OPTIONAL. This recognizes the fact that support for private annotations may introduce significantly more complexity to a server in terms of tracking ownership of the annotations, how quota is determined for users based on their own annotations, etc. 4. IMAP Protocol Changes 4.1. General Considerations The new SETMETADATA command and the METADATA response each have a mailbox name argument. An empty string is used for the mailbox name to signify server annotations. A non-empty string is used to signify mailbox annotations attached to the corresponding mailbox. Servers SHOULD ensure that mailbox annotations are automatically moved when the mailbox they refer to is renamed, i.e., the annotations follow the mailbox. This applies to a rename of the INBOX, with the additional behavior that the annotations are copied from the original INBOX to the renamed mailbox, i.e., mailbox annotations are preserved on the INBOX when it is renamed. Servers SHOULD delete annotations for a mailbox when the mailbox is deleted, so that a mailbox created with the same name as a previously existing mailbox does not inherit the old mailbox annotations. Servers SHOULD allow annotations on all 'types' of mailboxes, including ones reporting \Noselect for their LIST response. Servers can implicitly remove \Noselect mailboxes when all child mailboxes are removed, and, at that time any annotations associated with the \Noselect mailbox SHOULD be removed. The server is allowed to impose limitations on the size of any one annotation or the total number of annotations for a single mailbox or for the server as a whole. However, the server MUST accept an annotation data size of at least 1024 bytes, and an annotation count per server or mailbox of at least 10. Some annotations may be "read-only" -- i.e., they are set by the server and cannot be changed by the client. Also, such annotations may be "computed" -- i.e., the value changes based on underlying properties of the mailbox or server. For example, an annotation reporting the total size of all messages in the mailbox would change as messages are added or removed. Or, an annotation containing an IMAP URL for the mailbox would change if the mailbox was renamed. Servers MAY support sending unsolicited responses for use when annotations are changed by some "third-party" (see Section 4.4). In order to do so, servers MUST support the ENABLE command [RFC5161] and MUST only send unsolicited responses if the client used the ENABLE command [RFC5161] extension with the capability string "METADATA" or "METADATA-SERVER" earlier in the session, depending on which of those capabilities is supported by the server. 4.2. GETMETADATA Command This extension adds the GETMETADATA command. This allows clients to retrieve server or mailbox annotations. This command is only available in authenticated or selected state [RFC3501]. Arguments: mailbox-name options entry-specifier Responses: required METADATA response Result: OK - command completed NO - command failure: can't access annotations on the server BAD - command unknown or arguments invalid When the mailbox name is the empty string, this command retrieves server annotations. When the mailbox name is not empty, this command retrieves annotations on the specified mailbox. Options MAY be included with this command and are defined below. Example: C: a GETMETADATA "" /shared/comment S: * METADATA "" (/shared/comment "Shared comment") S: a OK GETMETADATA complete In the above example, the contents of the value of the "/shared/ comment" server entry is requested by the client and returned by the server. Example: C: a GETMETADATA "INBOX" /private/comment S: * METADATA "INBOX" (/private/comment "My own comment") S: a OK GETMETADATA complete In the above example, the contents of the value of the "/private/ comment" mailbox entry for the mailbox "INBOX" is requested by the client and returned by the server. Entry specifiers can be lists of atomic specifiers, so that multiple annotations may be returned in a single GETMETADATA command. Example: C: a GETMETADATA "INBOX" (/shared/comment /private/comment) S: * METADATA "INBOX" (/shared/comment "Shared comment" /private/comment "My own comment") S: a OK GETMETADATA complete In the above example, the values of the two server entries "/shared/comment" and "/private/comment" on the mailbox "INBOX" are requested by the client and returned by the server. 4.2.1. MAXSIZE GETMETADATA Command Option
EID 2785 (Verified) is as follows:

Section: 4.2.1

Original Text:

 |         C: a GETMETADATA "INBOX" (MAXSIZE 1024)
                                    (/shared/comment /private/comment)
           S: * METADATA "INBOX" (/private/comment "My own comment")
           S: a OK [METADATA LONGENTRIES 2199] GETMETADATA complete

Corrected Text:

 |         C: a GETMETADATA (MAXSIZE 1024) "INBOX"
                                    (/shared/comment /private/comment)
           S: * METADATA "INBOX" (/private/comment "My own comment")
           S: a OK [METADATA LONGENTRIES 2199] GETMETADATA complete
Notes:
GETMETADATA examples with options are wrong. ABNF says the options should be before mailbox name, not after. (Having them after mailbox name would also make the parsing more difficult since it could be confused with entries-list).
When the MAXSIZE option is specified with the GETMETADATA command, it restricts which entry values are returned by the server. Only entry values that are less than or equal in octet size to the specified MAXSIZE limit are returned. If there are any entries with values larger than the MAXSIZE limit, the server MUST include the METADATA LONGENTRIES response code in the tagged OK response for the GETMETADATA command. The METADATA LONGENTRIES response code returns the size of the biggest entry value requested by the client that exceeded the MAXSIZE limit. Example: C: a GETMETADATA "INBOX" (MAXSIZE 1024) (/shared/comment /private/comment) S: * METADATA "INBOX" (/private/comment "My own comment") S: a OK [METADATA LONGENTRIES 2199] GETMETADATA complete In the above example, the values of the two server entries "/shared/comment" and "/private/comment" on the mailbox "INBOX" are requested by the client, which wants to restrict the size of returned values to 1024 octets. In this case, the "/shared/ comment" entry value is 2199 octets and is not returned. 4.2.2. DEPTH GETMETADATA Command Option
EID 2786 (Verified) is as follows:

Section: 4.2.2

Original Text:

 |         C: a GETMETADATA "INBOX" (DEPTH 1)
                                   (/private/filters/values)
           S: * METADATA "INBOX" (/private/filters/values/small
                "SMALLER 5000" /private/filters/values/boss
                "FROM \"boss@example.com\"")
           S: a OK GETMETADATA complete

Corrected Text:

 |         C: a GETMETADATA (DEPTH 1) "INBOX"
                                   (/private/filters/values)
           S: * METADATA "INBOX" (/private/filters/values/small
                "SMALLER 5000" /private/filters/values/boss
                "FROM \"boss@example.com\"")
           S: a OK GETMETADATA complete
Notes:
Same reason as for the section 4.2.1 errata.
When the DEPTH option is specified with the GETMETADATA command, it extends the list of entry values returned by the server. For each entry name specified in the GETMETADATA command, the server returns the value of the specified entry name (if it exists), plus all entries below the entry name up to the specified DEPTH. Three values are allowed for DEPTH: "0" - no entries below the specified entry are returned "1" - only entries immediately below the specified entry are returned "infinity" - all entries below the specified entry are returned Thus, "depth 1" for an entry "/a" will match "/a" as well as its children entries (e.g., "/a/b"), but will not match grandchildren entries (e.g., "/a/b/c"). If the DEPTH option is not specified, this is the same as specifying "DEPTH 0". Example: C: a GETMETADATA "INBOX" (DEPTH 1) (/private/filters/values) S: * METADATA "INBOX" (/private/filters/values/small "SMALLER 5000" /private/filters/values/boss "FROM \"boss@example.com\"") S: a OK GETMETADATA complete In the above example, 2 entries below the /private/filters/values entry exist on the mailbox "INBOX": "/private/filters/values/ small" and "/private/filters/values/boss". 4.3. SETMETADATA Command This extension adds the SETMETADATA command. This allows clients to set annotations. This command is only available in authenticated or selected state [RFC3501]. Arguments: mailbox-name list of {entry, value} pairs
EID 1692 (Verified) is as follows:

Section: 4.3, pg.11

Original Text:

       Arguments:  mailbox-name
|                  entry
|                  value
|                  list of entry, values

Corrected Text:

       Arguments:  mailbox-name
|                  list of {entry, value} pairs
Notes:
Location is top of page 11.

Rationale:
The prose version of the syntax specification is confusing.
The ABNF in Section 5 is much more specific, and the prose
should correspond to the ABNF. The relevant ABFN rules
in Section 5 (pg.14/15) are (stripped of comments):
setmetadata = "SETMETADATA" SP mailbox SP entry-values
entry-values = "(" entry-value *(SP entry-value) ")"
entry-value = entry SP value
Responses: no specific responses for this command Result: OK - command completed NO - command failure: can't set annotations, or annotation too big or too many BAD - command unknown or arguments invalid This command sets the specified list of entries by adding or replacing the specified values provided, on the specified existing mailboxes or on the server (if the mailbox argument is the empty string). Clients can use NIL for the value of entries it wants to remove. The server SHOULD NOT return a METADATA response containing the updated annotation data. Clients MUST NOT assume that a METADATA response will be sent, and MUST assume that if the command succeeds, then the annotation has been changed. If the server is unable to set an annotation because the size of its value is too large, the server MUST return a tagged NO response with a "[METADATA MAXSIZE NNN]" response code when NNN is the maximum octet count that it is willing to accept. If the server is unable to set a new annotation because the maximum number of allowed annotations has already been reached, the server MUST return a tagged NO response with a "[METADATA TOOMANY]" response code. If the server is unable to set a new annotation because it does not support private annotations on one of the specified mailboxes, the server MUST return a tagged NO response with a "[METADATA NOPRIVATE]" response code. When any one annotation fails to be set, resulting in a tagged NO response from the server, then the server MUST NOT change the values for other annotations specified in the SETMETADATA command. Example: C: a SETMETADATA INBOX (/private/comment {33} S: + ready for data My new comment across two lines. ) S: a OK SETMETADATA complete In the above example, the entry "/private/comment" for the mailbox "INBOX" is created (if not already present) and the value set to a multi-line string. Example: C: a SETMETADATA INBOX (/private/comment NIL) S: a OK SETMETADATA complete In the above example, the entry "/private/comment" is removed from the mailbox "INBOX". Multiple entries can be set in a single SETMETADATA command by listing entry-value pairs in the list. Example: C: a SETMETADATA INBOX (/private/comment "My new comment" /shared/comment "This one is for you!") S: a OK SETMETADATA complete In the above example, the entries "/private/comment" and "/shared/ comment" for the mailbox "INBOX" are created (if not already present) and the values set as specified. Example: C: a SETMETADATA INBOX (/private/comment "My new comment") S: a NO [METADATA TOOMANY] SETMETADATA failed In the above example, the server is unable to set the requested (new) annotation as it has reached the limit on the number of annotations it can support on the specified mailbox. 4.4. METADATA Response The METADATA response displays results of a GETMETADATA command, or can be returned as an unsolicited response at any time by the server in response to a change in a server or mailbox annotation. When unsolicited responses are activated by the ENABLE [RFC5161] command for this extension, servers MUST send unsolicited METADATA responses if server or mailbox annotations are changed by a third- party, allowing servers to keep clients updated with changes. Unsolicited METADATA responses MUST only contain entry names, not the values. If the client wants to update any cached values, it must explicitly retrieve those using a GETMETADATA command. The METADATA response can contain multiple entries in a single response, but the server is free to return multiple responses for each entry or group of entries, if it desires. This response is only available in authenticated or selected state [RFC3501]. 4.4.1. METADATA Response with Values The response consists of a list of entry-value pairs. Example: C: a GETMETADATA "" /shared/comment S: * METADATA "" (/shared/comment "My comment") S: a OK GETMETADATA complete In the above example, a single entry with its value is returned by the server. Example: C: a GETMETADATA "INBOX" (/private/comment /shared/comment) S: * METADATA "INBOX" (/private/comment "My comment" /shared/comment "Its sunny outside!") S: a OK GETMETADATA complete In the above example, two entries and their values are returned by the server. Example: C: a GETMETADATA "INBOX" (/private/comment /shared/comment) S: * METADATA "INBOX" (/private/comment "My comment") S: * METADATA "INBOX" (/shared/comment "Its sunny outside!") S: a OK GETMETADATA complete
EID 3868 (Verified) is as follows:

Section: 4.4.1

Original Text:

   Example:

           C: a GETMETADATA "INBOX" /private/comment /shared/comment
           S: * METADATA "INBOX" (/private/comment "My comment"
                                  /shared/comment "Its sunny outside!")
           S: a OK GETMETADATA complete

      In the above example, two entries and their values are returned by
      the server.

   Example:

           C: a GETMETADATA "INBOX" /private/comment /shared/comment
           S: * METADATA "INBOX" (/private/comment "My comment")
           S: * METADATA "INBOX" (/shared/comment "Its sunny outside!")
           S: a OK GETMETADATA complete

Corrected Text:

   Example:

           C: a GETMETADATA "INBOX" (/private/comment /shared/comment)
           S: * METADATA "INBOX" (/private/comment "My comment"
                                  /shared/comment "Its sunny outside!")
           S: a OK GETMETADATA complete

      In the above example, two entries and their values are returned by
      the server.

   Example:

           C: a GETMETADATA "INBOX" (/private/comment /shared/comment)
           S: * METADATA "INBOX" (/private/comment "My comment")
           S: * METADATA "INBOX" (/shared/comment "Its sunny outside!")
           S: a OK GETMETADATA complete
Notes:
ABNF in section 5 for "getmetadata" says that when requesting multiple metadata entries, they must be part of a parenthesized list, and not simply space-separated:

getmetadata = "GETMETADATA" [SP getmetadata-options] SP mailbox SP entries
entries = entry / "(" entry *(SP entry) ")"
entry = astring
In the above example, the server returns two separate responses for each of the two entries requested. 4.4.2. Unsolicited METADATA Response without Values The response consists of a list of entries, each of which have changed on the server or mailbox. Example: C: a NOOP S: * METADATA "" /shared/comment S: a OK NOOP complete In the above example, the server indicates that the "/shared/ comment" server entry has been changed. Example: C: a NOOP S: * METADATA "INBOX" /shared/comment /private/comment S: a OK NOOP complete In the above example, the server indicates a change to two mailbox entries. 5. Formal Syntax The following syntax specification uses the Augmented Backus-Naur Form (ABNF) notation as specified in [RFC5234]. Non-terminals referenced but not defined below are as defined by [RFC3501], with the new definitions in [RFC4466] superseding those in [RFC3501]. Except as noted otherwise, all alphabetic characters are case- insensitive. The use of upper or lower case characters to define token strings is for editorial clarity only. Implementations MUST accept these strings in a case-insensitive fashion. capability =/ "METADATA" / "METADATA-SERVER" ; defines the capabilities for this extension. command-auth =/ setmetadata / getmetadata ; adds to original IMAP command entries = entry / "(" entry *(SP entry) ")" ; entry specifiers entry = astring ; slash-separated path to entry ; MUST NOT contain "*" or "%" entry-value = entry SP value entry-values = "(" entry-value *(SP entry-value) ")" entry-list = entry *(SP entry) ; list of entries used in unsolicited ; METADATA response getmetadata = "GETMETADATA" [SP getmetadata-options] SP mailbox SP entries ; empty string for mailbox implies ; server annotation. getmetadata-options = "(" getmetadata-option *(SP getmetadata-option) ")" getmetadata-option = tagged-ext-label [SP tagged-ext-val] ; tagged-ext-label and tagged-ext-val ; are defined in [RFC4466]. maxsize-opt = "MAXSIZE" SP number ; Used as a getmetadata-option metadata-resp = "METADATA" SP mailbox SP (entry-values / entry-list) ; empty string for mailbox implies ; server annotation. response-payload =/ metadata-resp ; adds to original IMAP data responses resp-text-code =/ "METADATA" SP "LONGENTRIES" SP number ; new response codes for GETMETADATA resp-text-code =/ "METADATA" SP ("MAXSIZE" SP number / "TOOMANY" / "NOPRIVATE") ; new response codes for SETMETADATA ; failures scope-opt = "DEPTH" SP ("0" / "1" / "infinity") ; Used as a getmetadata-option setmetadata = "SETMETADATA" SP mailbox SP entry-values ; empty string for mailbox implies ; server annotation. value = nstring / literal8 6. IANA Considerations All entries MUST have either "/shared" or "/private" as a prefix. Entry names MUST be specified in a Standards Track or IESG-approved Experimental RFC, or fall under the vendor namespace (i.e., use /shared/vendor/<vendor-token> or /private/vendor/<vendor-token> as the prefix). Each entry registration MUST include a content-type that is used to indicate the nature of the annotation value. Where applicable, a charset parameter MUST be included with the content-type. 6.1. Entry and Attribute Registration Template To: iana@iana.org Subject: IMAP METADATA Entry Registration Type: [Either "Mailbox" or "Server"] Name: [the name of the entry] Description: [a description of what the entry is for] Content-type: [MIME Content-Type and charset for the entry value] RFC Number: [for entries published as RFCs] Contact: [email and/or physical address to contact for additional information] 6.2. Server Entry Registrations The following templates specify the IANA registrations of annotation entries specified in this document. 6.2.1. /shared/comment To: iana@iana.org Subject: IMAP METADATA Entry Registration Type: Server Name: /shared/comment Description: Defines a comment or note that is associated with the server and that is shared with authorized users of the server. Content-type: text/plain; charset=utf-8 RFC Number: RFC 5464 Contact: IMAP Extensions mailto:ietf-imapext@imc.org 6.2.2. /shared/admin To: iana@iana.org Subject: IMAP METADATA Entry Registration Type: Server Name: /shared/admin Description: Indicates a method for contacting the server administrator. The value MUST be a URI (e.g., a mailto: or tel: URL). This entry is always read-only -- clients cannot change it. It is visible to authorized users of the system. Content-type: text/plain; charset=utf-8 RFC Number: RFC 5464 Contact: IMAP Extensions mailto:ietf-imapext@imc.org 6.3. Mailbox Entry Registrations The following templates specify the IANA registrations of annotation entries specified in this document. 6.3.1. /shared/comment To: iana@iana.org Subject: IMAP METADATA Entry Registration Type: Mailbox Name: /shared/comment Description: Defines a shared comment or note associated with a mailbox. Content-type: text/plain; charset=utf-8 RFC Number: RFC 5464 Contact: IMAP Extensions mailto:ietf-imapext@imc.org 6.3.2. /private/comment To: iana@iana.org Subject: IMAP METADATA Entry Registration Type: Mailbox Name: /private/comment Description: Defines a private comment or note associated with a mailbox. Content-type: text/plain; charset=utf-8 RFC Number: RFC 5464 Contact: IMAP Extensions mailto:ietf-imapext@imc.org 7. Security Considerations The security considerations in Section 11 of [RFC3501] apply here with respect to protecting annotations from snooping. Servers MAY choose to only support the METADATA and/or METADATA-SERVER extensions after a privacy layer has been negotiated by the client. Annotations can contain arbitrary data of varying size. As such, servers MUST ensure that size limits are enforced to prevent a user from using up all available space on a server and preventing use by others. Clients MUST treat annotation data values as an "untrusted" source of data as it is possible for it to contain malicious content. Annotations whose values are intended to remain private MUST be stored only in entries that have the "/private" prefix on the entry name. Excluding the above issues, the METADATA extension does not raise any security considerations that are not present in the base IMAP protocol, and these issues are discussed in [RFC3501]. 8. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2244] Newman, C. and J. Myers, "ACAP -- Application Configuration Access Protocol", RFC 2244, November 1997. [RFC3501] Crispin, M., "INTERNET MESSAGE ACCESS PROTOCOL - VERSION 4rev1", RFC 3501, March 2003. [RFC4314] Melnikov, A., "IMAP4 Access Control List (ACL) Extension", RFC 4314, December 2005. [RFC4466] Melnikov, A. and C. Daboo, "Collected Extensions to IMAP4 ABNF", RFC 4466, April 2006. [RFC5161] Gulbrandsen, A. and A. Melnikov, "The IMAP ENABLE Extension", RFC 5161, March 2008. [RFC5234] Crocker, D. and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68, RFC 5234, January 2008. Appendix A. Acknowledgments The ideas expressed in this document are based on the message annotation document that was co-authored by Randall Gellens. The author would like to thank the following individuals for contributing their ideas and support for writing this specification: Dave Cridland, Arnt Gulbrandsen, Dan Karp, Alexey Melnikov, Ken Murchison, Chris Newman, and Michael Wener. Author's Address Cyrus Daboo Apple Inc. 1 Infinite Loop Cupertino, CA 95014 USA EMail: cyrus@daboo.name URI: http://www.apple.com/ Full Copyright Statement Copyright (C) The IETF Trust (2009). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.